Let me show you how to make a lampshade using your favorite fabric.
Thrift stores and yard sales are my favorite place to find really awesome lamps.
New lamps are crazy expensive but you can find really beautiful and unique lamps secondhand for super cheap.
This post was sponsored by I Like That Lamp. This project and all opinions are my own. This post also contains affiliate links. If you make a purchase using those links, I may receive a small percentage at no additional cost to you. See my full disclosure here.
The problem is they usually have either ugly, outdated shades or no lampshades at all.
That doesn’t sound like such a big problem but it can turn into a huge headache.
A couple of years ago I found a gorgeous pair of turquoise lamps at a thrift store.
I was so excited because not only were they beautiful, but finding a matching pair is a total score!
Of course, they had no shades, but I figured I’d pick up a pair of new lampshades at Target, and problem solved.
Except for problem not solved. All the cute drum shades I found at Target and my other usual spots were the wrong size.
It took me over a year to find a pair of lampshades that would work with my beautiful vintage lamps.
Well a few weeks ago, I found another fabulous pair of vintage lamps at a local thrift store. Of course, there were no shades, but they were tall and curvy, and beautiful.
And only $7 for the pair! So it seemed like the perfect time to learn how to make a lampshade.
I wasn’t totally sure how it was going to turn out. I’ve tried to make my own DIY lampshade once in the past and it didn’t turn out so great.
It looked good from a distance but up close, it was kind of a mess.
But I wanted to give making a lampshade another try and this time I had two huge advantages – I was using real lampshade parts and I had great instructions to follow.
So yeah, it’s probably no surprise that it turned out 1000 times better.
This time around my DIY lampshades look exactly the way I pictured them.
Materials for making a DIY lampshade
- Adhesive styrene sheet for making lampshades
- Rotary cutter and cutting mat or scissors for cutting fabric
- lamp glue and small binder clips
- small paintbrush
- set of wire lampshade rings
- lamp harp set (if your lamp doesn’t already have one)
- fabric of your choice (I used Premier Prints Manchester fabric in french gray. The 10% discount does not apply to this item.)
- measuring tape
How to make a lampshade
Before you start making your lampshade or even order your supplies, you need to measure your lamp to figure out the correct size (both height and diameter).
It may seem like a small detail, but the right size lampshade makes a huge difference to the look of the finished lamp.
I Like That Lamp has a really good guide to figuring out what size lampshade you need right here.
I followed this video tutorial from I Like That Lamp when putting together my lampshades and it was really helpful.
But if you prefer written directions and tips, read on!
Before you begin, you need to iron your fabric. (I hate ironing and never iron my clothes, but I did iron my lampshade fabric because nobody wants a wrinkly lampshade.)
You may need to trim the length of your styrene sheet before you begin. (Styrene is the stiff material that gives the lampshade its shape.)
Just follow the size guide linked above to figure out how big it needs to be.
Lay your fabric out on a flat surface and stick the styrene sheet to it.
One side of the styrene is sticky so you simply peel the protective layer off the styrene slowly while unrolling it and sticking it onto the fabric.
Trim the fabric so that there is a half inch border of fabric above and below the styrene.
Also leave a half inch border on one of the short ends but cut the other short end of the fabric flush with the styrene.
Fold the extra fabric from the short end over the styrene and glue it there with lamp glue.
Fold the fabric/styrene into a loop and use a binder clip to secure it together.
The short end with the fabric border should be on top.
Set the lampshade up. Slide the ring with the washer into the lampshade.
You might need to adjust the size of your lampshade so that it fits snugly around the ring and hold it in place using binder clips.
Add glue to the excess fabric around the top of the shade in small sections.
Use a small paintbrush to spread the glue to cover the fabric as well as the metal of the ring.
The glue will become tacky after a few seconds and then you can fold it over the ring.
Use the binder clips to help hold it in place while you move on to the next section.
Flip over the shade and repeat the same process on the bottom using the plain wire ring.
Finally add a little glue to the seam going up the side of the lampshade.
The whole process took about an hour for my first lampshade. Once I knew what I was doing, the second went a bit faster.
Then they are ready to attach. If all you needed was a lampshade then you’re set.
I also added a lamp harp set to each of my lamps to support the new lampshades.
Here’s the finished product! I am so happy that I learned how to make my own lampshades.
Now I have a pair of completely custom lampshades and my $7 lamps look like a million bucks.
Originally I was planning to paint the lamps themselves but once the new shades were on, they really didn’t need any other updates.
These lamps came at the perfect time since I stole the lamps that were in here for my $100 family room makeover this fall. This pair is perfect in here.
Ok, so who else has been hoarding old lamps waiting for that perfect lampshade to come along?
Clear out the hoard and create the perfect custom lampshade!
- Adhesive styrene sheet
- Small binder clips
- Set of wire lampshade rings
- Lamp harp set (if your lamp doesn’t already have one)
- Fabric of your choice
- Rotary cutter and cutting mat
- Small paintbrush
- Measuring tape
- Lamp glue
- Iron your fabric.
- Lay it on a flat surface and stick the styrene sheet to it.
- Trim the fabric leaving a half inch border above and below the styrene.
- Fold it from the short end over the styrene and glue it with lamp glue.
- Fold the fabric/styrene into a loop.
- Secure with a binder clip.
- Slide the ring with the washer into the lampshade.
- Add glue around the top of the shade in small sections.
- Spread the glue to cover the fabric, as well as the metal of the ring, using the paint brush.
- Hold it in place with the binder clips.
- Repeat the same process on the bottom using the plain wire ring.
- Add glue to the seam on the side of the lampshade.
As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases.
Premier Prints French Grey Manchester, Yard
Nickel Silver Lamp Harp Set - Attachment for Table and Floor Lamps, Includes Harp, Saddle (Base) and Finial, 1-pack
Lamp Shade Ring Set to Make a DIY Drum Ring Lamp Shade
Lampshade Glue Kit - Includes Tacky Glue + 6 Binder Clips + Moulding Stick
Adhesive Pressure Sensitive Styrene Sheet Making DIY Lampshades in a Pre-Cut Length
Here are links to some of my other DIY light projects in case you missed them:
- Upcycle An Old Globe Into A Fabulous Light
- Vintage Camera Lamp
- How to Turn a Lantern into a Lamp
Have a fantastic week!